• Don't forget to rate 1-5 stars! Check the support tab for any help or comments.

  • (3)
    « »

    Installer for P-ROC Environment Software. Tested with Windows 7.

    The P-ROC (Pinball - Remote Operations Controller) is a circuit board that enables a computer to control a pinball machine over USB. More info at

    http://www.pinballcontrollers.com/index.php/products/p-roc

    Please refer to the tutorial below :

    https://vpinball.com/?post_type=cmdm_page&p=32020

    - initial release

    v2.0

    -fixed dmd layers issue

    -fixed multiball issue with more than 2 balls

    v3.0

    -software update to Python 2.7

    v3.1

    -VPCOM register fix

    This topic contains 55 replies, has 17 voices, and was last updated by  Thalamus 3 days, 20 hours ago.

    Viewing 20 posts - 1 through 20 (of 56 total)
    • Author
      Posts
    • #32029
       ninuzzu 
      Participant
      vipMember

      Installer for P-ROC Environment Software. Tested with Windows 7.

      The P-ROC (Pinball - Remote Operations Controller) is a circuit board that enables a computer to control a pinball machine over USB. More info at

      http://www.pinballcontrollers.com/index.php/products/p-roc

      2 users thanked author for this post.
      #32520
       aubie11 
      Participant

      So following the tutorial, I get stuck on part 2.  I keep getting this error.

       

       

      Attachments:
      #32523
       randr 
      Keymaster
      ModeratorMember

      you ran step one from “c” drive or desktop folder?

      ********************************************************
      Messing with the VPinball app and push notifications.
      So if you haven't downloaded app yet what are you waiting for!?
      *******************************************************

      1 user thanked author for this post.
      #32560
       aubie11 
      Participant

      I ran from c:\pinball\PROC

      #32941
       Natedogg 
      Participant

      The comment about running it from C: was helpful, when I tried to run step 1 from a jump drive it didn’t work.  When I extracted them to the C: drive all three steps worked.  Thanks. :yahoo:

      Nate

      #32942
       Natedogg 
      Participant

      Now I am on the Install CCC step.  When I run that it says “unable to download”.  In the instructions it says it will download 300MB of data, is that from within the zip files or do I need to have an internet connection?  I am running from the C: drive as well.  I have VP 10.1 in a cab, not connected to the internet.  Thanks!

      Nate

      #32944
       randr 
      Keymaster
      ModeratorMember

      For the 300mb you need to be connected. or download files manually from another computer

      ********************************************************
      Messing with the VPinball app and push notifications.
      So if you haven't downloaded app yet what are you waiting for!?
      *******************************************************

      1 user thanked author for this post.
      #34430
       Johngreve 
      Participant
      Member

      Hello all,
      I’ve successfully performed the three install steps and get the message that P-ROC is working.
      Then when I perform the Install CCC step my computer seems to hang up forever in the Downloading Sounds step….at least that is my interpretation of what I see happening.
      In the black box are the three download steps
      Downloading Data
      Downloading DMD
      Downloading sounds
      It appears to hang here with the cursor blinking below The words Downloading sounds. I “think” it is still trying to download sound files??

      Is the bulk of the 300 Meg’s sound files?
      I know that I don’t have the fasted internet connection in the world but I’ve given it up to an hour to show something else after the above mentioned and nothing changes.
      Will I get a “installation complete” message of some sort after the successful completion of downloading the files?

      Thanks for the help and advice in advance.

      Edit: Patience is a virtue…….waited a bit longer and I did indeed get the message that the download was
      complete. Fired up the table and from what I see so far this looks fantastic. I need to adjust the DMD a bit,never had to do that before as I have a real DMD on my cabinet and am not used to seeing a DMD displayed on my backglass. Hopefully if I follow the instructions in the tutorial I should be able to get it where it belongs.
      Terrific work to the team! Thanks for this masterpiece!!

      #36151
       Chapel 
      Participant

      Can ask this question in a different thread if needed as I know this installer was not made specifically for the Evil Dead table. I have P-ROC installed and everything is running fine since the release. Thanks for putting this installer together and the Cactus Canyon Continued table. I began looking at the Evil Dead table and was wondering since P-ROC is installed and working, would I skip to the game setup part of the Evil Dead wiki to get it up and going. I believe it is the git clone game repository part. Or would I still need to do some of the earlier steps. Thanks guys for any help.

      #36152
       CarnyPriest 
      Participant
      Member

      I thought the project was no longer public. Password protected the code and did not give out the login details.

      1 user thanked author for this post.
      #36153
       Chapel 
      Participant

      Ah. Thanks for the info Carny. Did not know that so definitely just saved me some time and frustration. Otherwise I would have been :wacko:  trying to figure it out.

      #36203
       CarnyPriest 
      Participant
      Member

      It’s too bad. It’s really good project. I need to see if I can reach him.

      #36288
       Jodannar 
      Participant
      Member

      I was looking at setting up the Evil Dead table now that P-R-O-C was so easily configured with the installer for CC. I hadn’t attempted it before this. I think your assumption is correct Chapel. you would start at the gtihub repository clone steps if it is still accessible

      #75167
       randr 
      Keymaster
      ModeratorMember

      Thanks for the update :good:

      ********************************************************
      Messing with the VPinball app and push notifications.
      So if you haven't downloaded app yet what are you waiting for!?
      *******************************************************

      #75629
       Dr.Tom 
      Participant
      MemberContributor

      Once the proc for vp is working, can you download and play other table mods?  Would really love to play Earthshaker: Aftershock by Scott Danesi.  Where would you find the files?

      #75632
       Jesperpark 
      Participant
      Member

      Once the latest P-roc is installed and running, it makes installing other games much easier.  For example Evil dead is just drop the Ecil dead game folder into the games folder of P-roc. Of course there is games specific adjustments but the p-roc dmd will start working

      @carnypriest might know about aftershock??

      #75654
       Thalamus 
      Moderator
      ContributorMemberModerator

      To me it seems like it very hard to get the hands on the required table assets. Would just love to get my hands on any of those p-roc’.

      #75657
       CarnyPriest 
      Participant
      Member

      Once the latest P-roc is installed and running, it makes installing other games much easier. For example Evil dead is just drop the Ecil dead game folder into the games folder of P-roc. Of course there is games specific adjustments but the p-roc dmd will start working @carnypriest might know about aftershock??

      No idea. Have you tried contacting the author? Aside from that, the VP table would have to be scripted.

      #75681
       Jesperpark 
      Participant
      Member

      Oh I thought this already was an existing visual pinball/p-roc project, my mistake.  I never heard of Aftershock before today

      #82107
       cyberpez 
      Participant
      Member

      Finally getting this set back up on my cab after a reload and running into a bit of an issue.  The first 3 steps all complete fine, but when I run the install ccc.bat it fails on downloading the code.  I tried on two different computers (both win10) and I get the same..  I’ve tried re-running the installer but the second time is skips sounds and dmds and errors on the code download again pretty quick.  Any ideas?

      p-roc-error

       

       

      Attachments:
      1 user thanked author for this post.
    Viewing 20 posts - 1 through 20 (of 56 total)

    You must be logged in to reply to this topic.

  • Please login to download.

  • ©2019 VPinBall.com

    WP2FB Auto Publish Powered By : XYZScripts.com
    Vpinball.com

    Log in with your credentials

    or    

    Forgot your details?

    Create Account