AndersE

Funny you bring this up as I was just talking to another member about similar thing last night! i prefer to run sound with flippers so I get the sound and the feel just seems better to me as the contractors give a great feel but sound nothing like a solenoid so the sound just works great along with real feedback in my opinion I’ll also say I d…[Read more]

Good looking, but where do i find the backglass?

yeah partyland is nice. You mean there ARE some tables but in FuturePinball?

Are you driving rgb leds via a relay? Then it must be the pwm’ing, as you can’t pwm a relay.

If DOF sends 100% pwm then it’ll be ok, but as soon the table wants to fade the led then it’s ca-ca..

and you will hear humming from the coil..

Are you driving rgb leds via a relay? Then it must be the pwm’ing, as you can’t pwm a relay.

If DOF sends 100% pwm then it’ll be ok, but as soon the table wants to fade the led then it’s ca-ca..

randr: you wrote just the same time i did ;) But now it is nighty-night here. Well after midnight.. Good night.

ranr: you wrote just the same time i did ;) But now it is nighty-night here. Well after midnight.. Good night.

whoho did i find a bug?

I was looking at the top dropdown menu for the place to change location.

But it was down the right where the “vpinball chat” is, the menu right of it..

I clicked there and selected edit profile.. haha..

yeah well.. i have gone through every menu and submenu of settings and profile, and there is nothing.

Sure i can enter favourite pinball, or website etc…etc.. but i can’t find location anywhere.

I bought a really crappy 12v batterypowered drill and slaughtered it ;) The motor had dual shafts, there was a small fanblade connected to one side to cool the motor

when heavy load, and the other went into the gearbox. It works great as shaker in my cab.

Cool hehe.. I  have a tip here:  If you up your extrusion rate a tiny amount you will get better infill on the top-layers. And if you print it with ABS

you can acetone-smooth it so it would look really smooth.

This reminds me that i must upload my 3d printed rgb flipperbuttons design. Yes i also use a 3d printer for my vpin :)

I have printed l…[Read more]

I had some mishap with my screen too, I had it standing in the same room i saw’ed the parts to the cab. Some sawdust had found it’s way into the screen

and is stuck between the backlight and the lcd. So when bright image i can see some small specks. But it is only on 2-3 places, one dustspeck per place and

only in the outer parts of the screen.…[Read more]

How’s it going? The link is broken..

Hey, do you have an internal vsync switch in this table? Because it starts at 160fps and then stays rocksolid at 60fps after gamestart even with vsync set at 0 in vpx.1.

This was excellent, it solved my low fps problem i wrote about in another thread.

I just have a question, where have the setting for ultradmd color gone? I got it only one time when pressing F1 in

americas most wanted (to turn the dmd off) , then i can’t get it again and i want to change the palette.

If i start the UltraDMD.exe nothing happens…[Read more]

This was excellent, it solved my low fps problem i wrote about in another thread.

I just have a question, where have the setting for ultradmd color gone? I got it only one time when pressing F1 in

americas most wanted (to turn the dmd off) , then i can’t get it again and i want to change the palette. And i can’t find the exe for it…[Read more]

This was excellent, it solved my low fps problem i wrote about in another thread.

I just have a question, where have the setting for ultradmd color gone? I got it only one time when pressing F1 in

americas most wanted, then i can’t get it again and i want to change the palette. And i can’t find the exe for it either.