Topic: addressable leds not working please help

This topic has 39 replies, 2 voices, and was last updated 3 years, 5 months ago by tommyducati67.

Viewing 20 posts - 1 through 20 (of 40 total)

1 2 →

Author

Posts
September 21, 2020 at 9:53 pm #201844
tommyducati67
Participant
@tommyducati67
Global config filename is “C:\DirectOutput\config\GlobalConfig_b2SServer.xml”
2020.09.13 17:46:17.022 Global config loaded from: C:\DirectOutput\config\GlobalConfig_b2SServer.xml
2020.09.13 17:46:17.022 Loading Pinball parts
2020.09.13 17:46:17.022 Loading cabinet
2020.09.13 17:46:17.022 Will load cabinet config file: C:\DirectOutput\Config\Cabinet.xml
2020.09.13 17:46:17.177 EXCEPTION: Could not load cabinet config from XML data.
2020.09.13 17:46:17.177 EXCEPTION: Thread:
2020.09.13 17:46:17.177 EXCEPTION: Message: Exception –> Could not deserialize the cabinet config from XML data.
2020.09.13 17:46:17.177 EXCEPTION: A exception occured when loading cabinet config file: C:\DirectOutput\Config\Cabinet.xml
2020.09.13 17:46:17.177 EXCEPTION: Thread:
2020.09.13 17:46:17.177 EXCEPTION: Message: NullReferenceException –> Object reference not set to an instance of an object.
2020.09.13 17:46:17.177 EXCEPTION: Stacktrace: at DirectOutput.Log.Exception(String Message, Exception E)
2020.09.13 17:46:17.177 EXCEPTION: Stacktrace: at DirectOutput.Cab.Cabinet.GetCabinetFromConfigXml(String ConfigXml)
2020.09.13 17:46:17.177 EXCEPTION: Stacktrace: at DirectOutput.Cab.Cabinet.GetCabinetFromConfigXmlFile(String FileName)
2020.09.13 17:46:17.177 EXCEPTION: Stacktrace: at DirectOutput.Cab.Cabinet.GetCabinetFromConfigXmlFile(FileInfo CabinetConfigFile)
2020.09.13 17:46:17.177 EXCEPTION: Stacktrace: at DirectOutput.Pinball.Setup(String GlobalConfigFilename, String TableFilename, String RomName)
2020.09.13 17:46:17.177 EXCEPTION: Targetsite: Void Exception(System.String, System.Exception)
2020.09.13 17:46:17.177 No cabinet config file loaded. Will use AutoConfig.
2020.09.13 17:46:17.177 Cabinet auto configuration started
2020.09.13 17:46:17.181 PhilipsHueAutoConfigurator.AutoConfig started…note, actual connection detection will happen asynchronously, and device disabled if not succesfull (check further down in the log)
2020.09.13 17:46:17.181 Opening 32-bit LedWiz driver…
2020.09.13 17:46:17.181 Detected and added LedWiz Nr. 1 with name LedWiz 01
2020.09.13 17:46:17.181 Added LedwizEquivalent Nr. 1 with name LedWiz 01 Equivalent for Ledwiz Nr. 1
2020.09.13 17:46:17.181 Cabinet auto configuration finished
2020.09.13 17:46:17.181 Cabinet loaded
2020.09.13 17:46:17.181 Loading table config
2020.09.13 17:46:17.181 No TableFilename specified, will use empty tableconfig
2020.09.13 17:46:17.181 Will try to load configs from DirectOutput.ini or LedControl.ini file(s) for RomName doflinx
2020.09.13 17:46:17.181 Loading LedControl file C:\DirectOutput\config\directoutputconfig.ini
2020.09.13 17:46:17.184 Min DOF Version is 0.8 for file directoutputconfig.ini
2020.09.13 17:46:17.361 Debug: Disposing LedWiz instance 01.
2020.09.13 17:46:17.576 Loading LedControl file C:\DirectOutput\config\directoutputconfig30.ini
2020.09.13 17:46:17.600 Min DOF Version is 0.8 for file directoutputconfig30.ini
2020.09.13 17:46:20.706 2 directoutputconfig.ini or ledcontrol.ini files loaded.
2020.09.13 17:46:20.706 Config for RomName doflinx exists in LedControl data. Updating cabinet and config.
2020.09.13 17:46:20.707 Table config loading finished: romname=doflinx, tablename=doflinx
2020.09.13 17:46:20.707 Pinball parts loaded
2020.09.13 17:46:20.707 Starting processes
2020.09.13 17:46:20.707 Initializing cabinet
2020.09.13 17:46:20.707 Debug: Initializing output controllers
2020.09.13 17:46:20.707 Debug: Initializing LedWiz Nr. 01
2020.09.13 17:46:20.707 LedWiz Nr. 01 initialized and updater thread initialized.
2020.09.13 17:46:20.707 Debug: Output controllers initialized
2020.09.13 17:46:20.707 Updater thread for LedWiz 01 started.
2020.09.13 17:46:20.707 Cabinet initialized
2020.09.13 17:46:20.708 Loading shape definition file: C:\DirectOutput\config\DirectOutputShapes.xml
2020.09.13 17:46:20.715 Framework initialized.
2020.09.13 17:46:20.715 Have fun! :)
2020.09.13 17:50:04.574 Finishing framework
2020.09.13 17:50:04.581 Finishing cabinet
2020.09.13 17:50:04.581 Debug: Finishing output controllers
2020.09.13 17:50:04.581 Debug: Finishing LedWiz Nr. 01
2020.09.13 17:50:04.661 Updater thread for LedWiz 01 terminated.
2020.09.13 17:50:04.692 LedWiz Nr. 01 finished and updater thread stopped.
2020.09.13 17:50:04.692 Debug: Output controllers finished
2020.09.13 17:50:04.692 Cabinet finished
2020.09.13 17:50:04.692 DirectOutput framework finished.
2020.09.13 17:50:04.692 Bye and thanks for using!

this is my cabinet file

?xml version=”1.0″?>
<Cabinet xmlns:xsi=”http://www.w3.org/2001/XMLSchema-instance” xmlns:xsd=”http://www.w3.org/2001/XMLSchema”>
<Name>Tommyducatipinball</Name>
<OutputControllers>

<TeensyStripController>
<Name>LedStripController</Name>
<NumberOfLedsStrip1>487</NumberOfLedsStrip1>
<NumberOfLedsStrip2>0</NumberOfLedsStrip2>
<NumberOfLedsStrip3>0</NumberOfLedsStrip3>
<NumberOfLedsStrip4>0</NumberOfLedsStrip4>
<NumberOfLedsStrip5>0</NumberOfLedsStrip5>
<NumberOfLedsStrip6>0</NumberOfLedsStrip6>
<NumberOfLedsStrip7>0</NumberOfLedsStrip7>
<NumberOfLedsStrip8>0</NumberOfLedsStrip8>
<ComPortName>COM4</ComPortName>
</TeensyStripController>

</OutputControllers>

<Toys>

<LedStrip>
<Name>BackBoard</Name>
<Width>32</Width>
<Height>8</Height>
<LedStripArrangement>TopDownAlternateLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>1</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Right</Name>
<Width>1</Width>
<Height>92</Height>
<LedStripArrangement>TopDownRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>257</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Left</Name>
<Width>1</Width>
<Height>91</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>349</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Left</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>440</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Right</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>464</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>car</Name>
<Width>1</Width>
<Height>7</Height>
<LedStripArrangement>TopDownRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber></FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedWizEquivalent>

<Name>LedWizEquivalent 30</Name>
<Outputs>

<LedWizEquivalentOutput>
<OutputName>BackBoard</OutputName>
<LedWizEquivalentOutputNumber>1</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Right</OutputName>
<LedWizEquivalentOutputNumber>4</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Left</OutputName>
<LedWizEquivalentOutputNumber>7</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Left</OutputName>
<LedWizEquivalentOutputNumber>10</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Right</OutputName>
<LedWizEquivalentOutputNumber>13</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>car</OutputName>
<LedWizEquivalentOutputNumber>16</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

</Outputs>
<LedWizNumber>30</LedWizNumber>
</LedWizEquivalent>

</Toys>

</Cabinet>

this is my global config

<?xml version=”1.0″ encoding=”utf-8″?>
<!–Global configuration for the DirectOutput framework.–>
<!–Saved by DirectOutput Version 3.1.7011.27968: 2020-09-06 14-14-39–>
<GlobalConfig>
<LedWizDefaultMinCommandIntervalMs>10</LedWizDefaultMinCommandIntervalMs>
<LedControlMinimumEffectDurationMs>60</LedControlMinimumEffectDurationMs>
<LedControlMinimumRGBEffectDurationMs>120</LedControlMinimumRGBEffectDurationMs>
<PacLedDefaultMinCommandIntervalMs>10</PacLedDefaultMinCommandIntervalMs>
<IniFilesPath />
<CabinetConfigFilePattern>C:\DirectOutput\Config\Cabinet.xml</CabinetConfigFilePattern>
<TableConfigFilePatterns />
<EnableLogging>true</EnableLogging>
<ClearLogOnSessionStart>true</ClearLogOnSessionStart>
<LogFilePattern>.\DirectOutput.log</LogFilePattern>
</GlobalConfig>

I’m new to the whole set up ,thank you in advance

You need to login in order to like this post: click here
September 21, 2020 at 10:40 pm #201847
outhere
Moderator
@outhere
@tommyducati67
This number should be 494
Then post a recent DirectOutput.log
When testing do not have this program running — doflinx
<NumberOfLedsStrip1>487</NumberOfLedsStrip1>

You need to login in order to like this post: click here
September 22, 2020 at 9:11 am #201889
tommyducati67
Participant
@tommyducati67
ah i see my mistake as far as count … the last entry of a strip

this entry shouldn’t be here , i dont have this in my build

<LedStrip>
<Name>car</Name>
<Width>1</Width>
<Height>7</Height>
<LedStripArrangement>TopDownRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber></FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>

can i just delete this whole strip entry? . i used a template from major frenchy and forgot to take this out .

i just have strips on right and left plus back and 2 rings for speakers totaling 487

i’ll disable doflinx and try again later today

thanks again for your help

You need to login in order to like this post: click here
September 22, 2020 at 9:13 am #201890
tommyducati67
Participant
@tommyducati67
Question Can i delete that last entry or do i have to generate another cabinet xml of course with deleting that last line to show a total of 487?

You need to login in order to like this post: click here
September 22, 2020 at 11:12 am #201897
outhere
Moderator
@outhere
delete this

<LedStrip>
<Name>car</Name>
<Width>1</Width>
<Height>7</Height>
<LedStripArrangement>TopDownRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber></FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

End this

<LedWizEquivalentOutput>
<OutputName>car</OutputName>
<LedWizEquivalentOutputNumber>16</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

You need to login in order to like this post: click here
September 22, 2020 at 1:45 pm #201911
tommyducati67
Participant
@tommyducati67
Delete this too? you typed end this

End this

<LedWizEquivalentOutput>
<OutputName>car</OutputName>
<LedWizEquivalentOutputNumber>16</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

You need to login in order to like this post: click here
September 22, 2020 at 2:18 pm #201913
outhere
Moderator
@outhere
tommyducati67 wrote:

Delete this too? you typed end this

End this

<LedWizEquivalentOutput>

<OutputName>car</OutputName>

<LedWizEquivalentOutputNumber>16</LedWizEquivalentOutputNumber>

</LedWizEquivalentOutput>

Delete this too?- Yes

And this

You need to login in order to like this post: click here
September 22, 2020 at 3:04 pm #201919
tommyducati67
Participant
@tommyducati67
Ok thanks again ?

You need to login in order to like this post: click here
September 22, 2020 at 7:36 pm #201928
tommyducati67
Participant
@tommyducati67
Resolved thank you for all your help ,deleted those to entries and everything came alive ?

You need to login in order to like this post: click here
October 20, 2020 at 8:13 pm #205789
tommyducati67
Participant
@tommyducati67
Hi Outhere , im running into another issue .. i tried to update the dof confid and now i cant get the leds to work at all

DirectOutput Version 3.1.7011.27968, built 2019.03.13 15:32
MJR Grander Unified DOF R3++ edition feat. Djrobx, Rambo3, and Freezy
DOF created by SwissLizard | https://github.com/mjrgh/DirectOutput
2020.10.18 14:56:44.493 DirectOutput Logger initialized
2020.10.18 14:56:44.477 Global config filename is “C:\DirectOutput\Config\GlobalConfig_B2S.Server.xml”
2020.10.18 14:56:44.493 Global config loaded from: C:\DirectOutput\Config\GlobalConfig_B2S.Server.xml
2020.10.18 14:56:44.493 Loading Pinball parts
2020.10.18 14:56:44.493 Loading cabinet
2020.10.18 14:56:44.493 Will load cabinet config file: C:\DirectOutput\Config\Cabinet.xml
2020.10.18 14:56:44.821 EXCEPTION: Could not load cabinet config from XML data.
2020.10.18 14:56:44.821 EXCEPTION: Thread:
2020.10.18 14:56:44.821 EXCEPTION: Message: Exception –> Could not deserialize the cabinet config from XML data.
2020.10.18 14:56:44.821 EXCEPTION: A exception occured when loading cabinet config file: C:\DirectOutput\Config\Cabinet.xml
2020.10.18 14:56:44.821 EXCEPTION: Thread:
2020.10.18 14:56:44.821 EXCEPTION: Message: NullReferenceException –> Object reference not set to an instance of an object.
2020.10.18 14:56:44.821 EXCEPTION: Stacktrace: at DirectOutput.Log.Exception(String Message, Exception E)
2020.10.18 14:56:44.821 EXCEPTION: Stacktrace: at DirectOutput.Cab.Cabinet.GetCabinetFromConfigXml(String ConfigXml)
2020.10.18 14:56:44.821 EXCEPTION: Stacktrace: at DirectOutput.Cab.Cabinet.GetCabinetFromConfigXmlFile(String FileName)
2020.10.18 14:56:44.821 EXCEPTION: Stacktrace: at DirectOutput.Cab.Cabinet.GetCabinetFromConfigXmlFile(FileInfo CabinetConfigFile)
2020.10.18 14:56:44.821 EXCEPTION: Stacktrace: at DirectOutput.Pinball.Setup(String GlobalConfigFilename, String TableFilename, String RomName)
2020.10.18 14:56:44.821 EXCEPTION: Targetsite: Void Exception(System.String, System.Exception)
2020.10.18 14:56:44.821 No cabinet config file loaded. Will use AutoConfig.
2020.10.18 14:56:44.821 Cabinet auto configuration started
2020.10.18 14:56:44.852 PhilipsHueAutoConfigurator.AutoConfig started…note, actual connection detection will happen asynchronously, and device disabled if not succesfull (check further down in the log)
2020.10.18 14:56:44.852 LedWiz-like device at VID=121, PID=6, product string=Generic USB Joystick , manufacturer string=DragonRise Inc.
2020.10.18 14:56:44.852 LedWiz-like device at VID=3727, PID=168, product string=2.4G RX, manufacturer string=DaKai
2020.10.18 14:56:44.852 LedWiz-like device at VID=3727, PID=168, product string=2.4G RX, manufacturer string=DaKai
2020.10.18 14:56:44.852 LedWiz-like device at VID=64250, PID=240, product string=LED-Wiz, manufacturer string=GGG
2020.10.18 14:56:44.852 HID caps: usage page=12, usage=1, number of link collection nodes=1, output report byte length=9
2020.10.18 14:56:44.868 LedWiz-like device at VID=3727, PID=168, product string=2.4G RX, manufacturer string=DaKai
2020.10.18 14:56:44.868 Opening 32-bit LedWiz driver…
2020.10.18 14:56:44.868 Detected and added LedWiz Nr. 1 with name LedWiz 01
2020.10.18 14:56:44.868 Added LedwizEquivalent Nr. 1 with name LedWiz 01 Equivalent for Ledwiz Nr. 1
2020.10.18 14:56:44.868 Cabinet auto configuration finished
2020.10.18 14:56:44.868 Cabinet loaded
2020.10.18 14:56:44.868 Loading table config
2020.10.18 14:56:44.868 No TableFilename specified, will use empty tableconfig
2020.10.18 14:56:44.868 Cant load config from directoutput.ini or ledcontrol.ini file(s) since no RomName was supplied. No ledcontrol config will be loaded.
2020.10.18 14:56:44.868 Table config loading finished: romname=, tablename=
2020.10.18 14:56:44.868 Pinball parts loaded
2020.10.18 14:56:44.868 Starting processes
2020.10.18 14:56:44.868 Initializing cabinet
2020.10.18 14:56:44.868 Debug: Initializing output controllers
2020.10.18 14:56:44.868 Debug: Initializing LedWiz Nr. 01
2020.10.18 14:56:44.868 LedWiz Nr. 01 initialized and updater thread initialized.
2020.10.18 14:56:44.868 Debug: Output controllers initialized
2020.10.18 14:56:44.868 Updater thread for LedWiz 01 started.
2020.10.18 14:56:44.868 Cabinet initialized
2020.10.18 14:56:44.883 Loading shape definition file: C:\DirectOutput\Config\DirectOutputShapes.xml
2020.10.18 14:56:44.914 Framework initialized.
2020.10.18 14:56:44.914 Have fun! :)
2020.10.18 14:57:45.188 Finishing framework
2020.10.18 14:57:45.188 Finishing cabinet
2020.10.18 14:57:45.188 Debug: Finishing output controllers
2020.10.18 14:57:45.188 Debug: Finishing LedWiz Nr. 01
2020.10.18 14:57:45.188 Updater thread for LedWiz 01 terminated.
2020.10.18 14:57:45.219 LedWiz Nr. 01 finished and updater thread stopped.
2020.10.18 14:57:45.219 Debug: Output controllers finished
2020.10.18 14:57:45.219 Cabinet finished
2020.10.18 14:57:45.219 DirectOutput framework finished.
2020.10.18 14:57:45.219 Bye and thanks for using!
2020.10.18 14:57:45.235 Debug: Disposing LedWiz instance 01.

I tired to disable doflinx thru alt delete but looks like it still pops up

You need to login in order to like this post: click here
October 20, 2020 at 8:18 pm #205790
tommyducati67
Participant
@tommyducati67
this is the Cab file

<?xml version=”1.0″?>
<Cabinet xmlns:xsi=”http://www.w3.org/2001/XMLSchema-instance” xmlns:xsd=”http://www.w3.org/2001/XMLSchema”>
<Name>Tommyducatipinball</Name>
<OutputControllers>

<TeensyStripController>
<Name>LedStripController</Name>
<NumberOfLedsStrip1>487</NumberOfLedsStrip1>
<NumberOfLedsStrip2>0</NumberOfLedsStrip2>
<NumberOfLedsStrip3>0</NumberOfLedsStrip3>
<NumberOfLedsStrip4>0</NumberOfLedsStrip4>
<NumberOfLedsStrip5>0</NumberOfLedsStrip5>
<NumberOfLedsStrip6>0</NumberOfLedsStrip6>
<NumberOfLedsStrip7>0</NumberOfLedsStrip7>
<NumberOfLedsStrip8>0</NumberOfLedsStrip8>
<ComPortName>COM4</ComPortName>
</TeensyStripController>

</OutputControllers>

<Toys>

<LedStrip>
<Name>BackBoard</Name>
<Width>32</Width>
<Height>8</Height>
<LedStripArrangement>TopDownAlternateLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>1</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Right</Name>
<Width>1</Width>
<Height>92</Height>
<LedStripArrangement>TopDownRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>257</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Left</Name>
<Width>1</Width>
<Height>91</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>349</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Left</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>440</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Right</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>RightUpLeftD own</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>464</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedWizEquivalent>

<Name>LedWizEquivalent 30</Name>
<Outputs>

<LedWizEquivalentOutput>
<OutputName>BackBoard</OutputName>
<LedWizEquivalentOutputNumber>1</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Right</OutputName>
<LedWizEquivalentOutputNumber>4</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Left</OutputName>
<LedWizEquivalentOutputNumber>7</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Left</OutputName>
<LedWizEquivalentOutputNumber>10</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Right</OutputName>
<LedWizEquivalentOutputNumber>13</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

Global Config

<?xml version=”1.0″ encoding=”utf-8″?>
<!–Global configuration for the DirectOutput framework.–>
<!–Saved by DirectOutput Version 3.1.7011.27968: 2020-10-18 14-02-48–>

</Outputs>
<LedWizNumber>30</LedWizNumber>
</LedWizEquivalent>

</Toys>

</Cabinet>

Global Config

<?xml version=”1.0″ encoding=”utf-8″?>
<!–Global configuration for the DirectOutput framework.–>
<!–Saved by DirectOutput Version 3.1.7011.27968: 2020-10-18 14-02-48–>
<GlobalConfig>
<LedWizDefaultMinCommandIntervalMs>10</LedWizDefaultMinCommandIntervalMs>
<LedControlMinimumEffectDurationMs>60</LedControlMinimumEffectDurationMs>
<LedControlMinimumRGBEffectDurationMs>120</LedControlMinimumRGBEffectDurationMs>
<PacLedDefaultMinCommandIntervalMs>10</PacLedDefaultMinCommandIntervalMs>
<IniFilesPath />
<CabinetConfigFilePattern>C:\DirectOutput\Config\Cabinet.xml</CabinetConfigFilePattern>
<TableConfigFilePatterns />
<EnableLogging>true</EnableLogging>
<ClearLogOnSessionStart>true</ClearLogOnSessionStart>
<LogFilePattern>.\DirectOutput.log</LogFilePattern>
</GlobalConfig>

Globalconfig_B2S

<?xml version=”1.0″ encoding=”utf-8″?>
<!–Global configuration for the DirectOutput framework.–>
<!–Saved by DirectOutput Version 3.1.7011.27968: 2020-10-18 14-05-35–>
<GlobalConfig>
<LedWizDefaultMinCommandIntervalMs>10</LedWizDefaultMinCommandIntervalMs>
<LedControlMinimumEffectDurationMs>60</LedControlMinimumEffectDurationMs>
<LedControlMinimumRGBEffectDurationMs>120</LedControlMinimumRGBEffectDurationMs>
<PacLedDefaultMinCommandIntervalMs>10</PacLedDefaultMinCommandIntervalMs>
<IniFilesPath />
<CabinetConfigFilePattern>C:\DirectOutput\Config\Cabinet.xml</CabinetConfigFilePattern>
<TableConfigFilePatterns />
<EnableLogging>true</EnableLogging>
<ClearLogOnSessionStart>true</ClearLogOnSessionStart>
<LogFilePattern>.\DirectOutput.log</LogFilePattern>
</GlobalConfig>

You need to login in order to like this post: click here
October 20, 2020 at 8:46 pm #205792
outhere
Moderator
@outhere
@tommyducati67
Are you sure you pasted your Cabinet file correctly

Why is this towards the bottom of your cabinet file

Global Config

<?xml version=”1.0″ encoding=”utf-8″?>
<!–Global configuration for the DirectOutput framework.–>
<!–Saved by DirectOutput Version 3.1.7011.27968: 2020-10-18 14-02-48–>

You need to login in order to like this post: click here
October 20, 2020 at 8:53 pm #205793
tommyducati67
Participant
@tommyducati67
my bad should have copied and pasted one at a time

this is the Cab xml

<?xml version=”1.0″?>
<Cabinet xmlns:xsi=”http://www.w3.org/2001/XMLSchema-instance” xmlns:xsd=”http://www.w3.org/2001/XMLSchema”>
<Name>Tommyducatipinball</Name>
<OutputControllers>

<TeensyStripController>
<Name>LedStripController</Name>
<NumberOfLedsStrip1>487</NumberOfLedsStrip1>
<NumberOfLedsStrip2>0</NumberOfLedsStrip2>
<NumberOfLedsStrip3>0</NumberOfLedsStrip3>
<NumberOfLedsStrip4>0</NumberOfLedsStrip4>
<NumberOfLedsStrip5>0</NumberOfLedsStrip5>
<NumberOfLedsStrip6>0</NumberOfLedsStrip6>
<NumberOfLedsStrip7>0</NumberOfLedsStrip7>
<NumberOfLedsStrip8>0</NumberOfLedsStrip8>
<ComPortName>COM4</ComPortName>
</TeensyStripController>

</OutputControllers>

<Toys>

<LedStrip>
<Name>BackBoard</Name>
<Width>32</Width>
<Height>8</Height>
<LedStripArrangement>TopDownAlternateLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>1</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Right</Name>
<Width>1</Width>
<Height>92</Height>
<LedStripArrangement>TopDownRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>257</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Left</Name>
<Width>1</Width>
<Height>91</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>349</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Left</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>440</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Right</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>RightUpLeftD own</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>464</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedWizEquivalent>

<Name>LedWizEquivalent 30</Name>
<Outputs>

<LedWizEquivalentOutput>
<OutputName>BackBoard</OutputName>
<LedWizEquivalentOutputNumber>1</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Right</OutputName>
<LedWizEquivalentOutputNumber>4</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Left</OutputName>
<LedWizEquivalentOutputNumber>7</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Left</OutputName>
<LedWizEquivalentOutputNumber>10</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Right</OutputName>
<LedWizEquivalentOutputNumber>13</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

</Outputs>
<LedWizNumber>30</LedWizNumber>
</LedWizEquivalent>

</Toys>

</Cabinet>

You need to login in order to like this post: click here
October 20, 2020 at 9:42 pm #205798
outhere
Moderator
@outhere
@tommyducati67 — Try this – it should work

<?xml version="1.0"?>
<Cabinet xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
<Name>Tommyducatipinball</Name>
<OutputControllers>

<TeensyStripController>
<Name>LedStripController</Name>
<NumberOfLedsStrip1>487</NumberOfLedsStrip1>
<NumberOfLedsStrip2>0</NumberOfLedsStrip2>
<NumberOfLedsStrip3>0</NumberOfLedsStrip3>
<NumberOfLedsStrip4>0</NumberOfLedsStrip4>
<NumberOfLedsStrip5>0</NumberOfLedsStrip5>
<NumberOfLedsStrip6>0</NumberOfLedsStrip6>
<NumberOfLedsStrip7>0</NumberOfLedsStrip7>
<NumberOfLedsStrip8>0</NumberOfLedsStrip8>
<ComPortName>COM4</ComPortName>
</TeensyStripController>

</OutputControllers>

<Toys>

<LedStrip>
<Name>BackBoard</Name>
<Width>32</Width>
<Height>8</Height>
<LedStripArrangement>TopDownAlternateLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>1</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Right</Name>
<Width>1</Width>
<Height>92</Height>
<LedStripArrangement>TopDownRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>257</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Left</Name>
<Width>1</Width>
<Height>91</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>349</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Left</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>440</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Right</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>BottomUpRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>464</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedWizEquivalent>

<Name>LedWizEquivalent 30</Name>
<Outputs>

<LedWizEquivalentOutput>
<OutputName>BackBoard</OutputName>
<LedWizEquivalentOutputNumber>1</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Right</OutputName>
<LedWizEquivalentOutputNumber>4</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Left</OutputName>
<LedWizEquivalentOutputNumber>7</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Left</OutputName>
<LedWizEquivalentOutputNumber>10</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Right</OutputName>
<LedWizEquivalentOutputNumber>13</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

</Outputs>
<LedWizNumber>30</LedWizNumber>
</LedWizEquivalent>

</Toys>

</Cabinet>

You need to login in order to like this post: click here
October 20, 2020 at 9:53 pm #205800
outhere
Moderator
@outhere
Make sure you start doing back ups
You can only use the ones on the list — http://pinball.weilenmann.net/docu/DirectOutputWIP/toy_builtin.html#use_DirectOutput_Cab_Toys_Hardware_LedStrip

@tommyducati67 — Take a look at the areas marked in Red those are the lines I fixed

<?xml version=”1.0″?>
<Cabinet xmlns:xsi=”http://www.w3.org/2001/XMLSchema-instance” xmlns:xsd=”http://www.w3.org/2001/XMLSchema”>
<Name>Tommyducatipinball</Name>
<OutputControllers>

<TeensyStripController>
<Name>LedStripController</Name>
<NumberOfLedsStrip1>487</NumberOfLedsStrip1>
<NumberOfLedsStrip2>0</NumberOfLedsStrip2>
<NumberOfLedsStrip3>0</NumberOfLedsStrip3>
<NumberOfLedsStrip4>0</NumberOfLedsStrip4>
<NumberOfLedsStrip5>0</NumberOfLedsStrip5>
<NumberOfLedsStrip6>0</NumberOfLedsStrip6>
<NumberOfLedsStrip7>0</NumberOfLedsStrip7>
<NumberOfLedsStrip8>0</NumberOfLedsStrip8>
<ComPortName>COM4</ComPortName>
</TeensyStripController>

</OutputControllers>

<Toys>

<LedStrip>
<Name>BackBoard</Name>
<Width>32</Width>
<Height>8</Height>
<LedStripArrangement>TopDownAlternateLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>1</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Right</Name>
<Width>1</Width>
<Height>92</Height>
<LedStripArrangement>TopDownRightLeft</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>257</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Sideboard Left</Name>
<Width>1</Width>
<Height>91</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>349</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Left</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>BottomUpLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>440</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedStrip>
<Name>Ring Right</Name>
<Width>1</Width>
<Height>24</Height>
<LedStripArrangement>RightUpLeftD own</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>464</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>LedStripController</OutputControllerName>
</LedStrip>

<LedWizEquivalent>

<Name>LedWizEquivalent 30</Name>
<Outputs>

<LedWizEquivalentOutput>
<OutputName>BackBoard</OutputName>
<LedWizEquivalentOutputNumber>1</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Right</OutputName>
<LedWizEquivalentOutputNumber>4</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Sideboard Left</OutputName>
<LedWizEquivalentOutputNumber>7</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Left</OutputName>
<LedWizEquivalentOutputNumber>10</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

<LedWizEquivalentOutput>
<OutputName>Ring Right</OutputName>
<LedWizEquivalentOutputNumber>13</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>

</Outputs>
<LedWizNumber>30</LedWizNumber>
</LedWizEquivalent>

</Toys>

</Cabinet>

You need to login in order to like this post: click here
October 21, 2020 at 11:55 am #205892
tommyducati67
Participant
@tommyducati67
OK Ill try that when i get off work

As always i wanna thank you for your patience in helping me with this , you guys rock

You need to login in order to like this post: click here
October 21, 2020 at 1:16 pm #205898
tommyducati67
Participant
@tommyducati67
I see now that its the cabinet address some funky stuff happened ..question what would cause the address to change like that ?

You need to login in order to like this post: click here
October 21, 2020 at 1:49 pm #205899
outhere
Moderator
@outhere
tommyducati67 wrote:

I see now that its the cabinet address some funky stuff happened ..question what would cause the address to change like that ?

Post Video

You need to login in order to like this post: click here
October 21, 2020 at 8:18 pm #205954
tommyducati67
Participant
@tommyducati67
i just checked my cab file and its the same as yours with the address not sure why when i copied pasted it here it shows those incorrect characters .. only thing i had to change is the last ring that you corrected in red …

so teensy has 2 files an alpha and a beta .. when i tried to upload them then using the arduino to verify and upload it reverts back to TeensystripController.ino.hex,5 not alpha or beta ?

You need to login in order to like this post: click here
October 21, 2020 at 8:57 pm #205956
outhere
Moderator
@outhere
tommyducati67 wrote:

i just checked my cab file and its the same as yours with the address not sure why when i copied pasted it here it shows those incorrect characters .. only thing i had to change is the last ring that you corrected in red …
so teensy has 2 files an alpha and a beta .. when i tried to upload them then using the arduino to verify and upload it reverts back to TeensystripController.ino.hex,5 not alpha or beta ?

I have never used a test program to check mine, I hook them up and they worked

You need to login in order to like this post: click here
Author

Posts